temperature test & conditioning applications

  • Resources
  • News
29
August
2016

Eco-friendly Thermal Test Systems Avoid Gas Law Leak Check Requirements

Saves cost of leak checking under new regulation

The environmentally friendly ECO series ThermoStream® temperature forcing systems will save users from additional maintenance costs under the EU F-Gas regulation for refrigeration systems... 

18
September
2015

Eco-friendly Electronics Thermal Test Systems

Consumes less energy with high performance and quiet operation

An environmentally friendly series of Temptronic® ThermoStream® temperature forcing systems that use less energy and operate with very low audible noise have been introduced by inTEST Thermal Solutions. The ECO Series temperature test systems operate on...

30
July
2015

Benchtop System for IC Temperature Testing

Efficient cooling and heating even with high-Watt emitting devices

Two benchtop systems for thermal testing and characterization of integrated circuits including high-Watt emitting devices have been introduced by inTEST Thermal..

10
March
2015

Temperature Cycling Traveling Wave Tubes

Two-zone plate provides thermal stress for satellite component

inTEST Thermal Solutions (iTS) has designed a multi-zone thermal plate for hot/cold temperature cycling of microwave signal amplifiers used in satellite data communications...

02
December
2014

Cryogenic vs. Compressor Based Cooling

Pros and Cons of Cooling Methods in Electronics Thermal Testing

Cryogenic vs. Compressor-based Cooling Systems, a technical paper exploring cooling methods used in electronics thermal testing, has been published by inTEST Thermal Solutions (iTS).

28
July
2014

iTS integrates temperature platform with Agilent’s power device analyzer

The integration of a temperature controlled thermal platform with the Agilent B1506A Power Device Analyzer has been introduced by inTEST Thermal Solutions and Agilent. The newly designed hot plate permits automated control of platform temperature, from enclosure ambient to 250°C, for characterization of power devices such as IGBTs and MOSFETs.

14
July
2014

iTS Launches Redesigned Website for Temperature Control Systems

Solutions for electronics and materials design and test

A redesigned website with temperature test and conditioning content for design and manufacturing engineers has been introduced by inTEST Thermal Solutions.

08
May
2014

Controller Enhances Thermal Verification and Burn-in of Electronics

A new control platform for Sigma Systems’ cryogenically and mechanically cooled thermal chambers and plates has been introduced by inTEST Thermal Solutions. Burn-in and testing of components, sensors, and PCBs typically involves temperature cycling from two to four points, which can be time consuming to setup and run. The new TS Controllerprovides touch-screen and remote interfacing to set up and transfer thermal profiles, view data and trends, and log diagnostics.

18
February
2014

Expanded Temperature System for Electronics Design and Test

A temperature control system for high-temperature testing of ICs, transceivers, and PCBs has been introduced by inTEST Thermal Solutions. The Thermostream® ATS-750 delivers clean dry air from -90 to 300°C to support growing demands for testing electronics that need to operate at higher temperatures.

19
December
2013

Replacement Controller for Thermal Chambers and Temperature Plates

A replacement controller for Sigma Systems thermal chambers and plates has been introduced by inTEST Thermal Solutions. The TSR controller matches both size and programming syntax of legacy C3 and C4 controllers...

27
November
2013

Mobile Temperature System Speeds Electronic Test & Verification

A mobile temperature control system for high-speed thermal testing of electronic components, sensors and PCBs has been introduced by inTEST Thermal Solutions. The Thermostream® ATS-535 brings temperatures (-60 to +225°C) to the test site by directing a stream of cooled or heated dry air without the need for an external air supply

01
January
2013

iTS launches ATS-Series ThermoStream® Temperature Forcing Systems

-100 to +300ºC Systems for Testing, Tuning, and Conditioning Electronic Devices, ICs, PCBs, MOSFETs, IGBTs, and Optical Transceivers

iTS has launched a comprehensive line of precision temperature forcing systems, the ATS-Series ThermoStream® systems. With temperature range extremes as high as +300ºC (570ºF) and as low as -100ºC (-148ºF), countless test and conditioning applications can now be solved with a compact, precise, and portable system.